Now showing circuits 49941-49960 of 51760. Sort by

basic transistor

basic transistor PUBLIC

by miceuz | updated June 14, 2012

base-emitter LED

base-emitter LED PUBLIC

by malin | updated June 14, 2012

Trip

Trip PUBLIC

by miceuz | updated June 14, 2012

Circuito Panel Solar a USB

Circuito Panel Solar a USB PUBLIC

by cavilad | updated June 14, 2012

Constant current regulator

Constant current regulator PUBLIC

This is a constant current mode of lead acid battery charger i'm building

by miceuz | updated June 14, 2012

constant-current-source   opamp  

opamp

opamp PUBLIC

by privatebangggg | updated June 13, 2012

Bass boost

Bass boost PUBLIC

by Plecto | updated June 13, 2012

frogs done circuit and

frogs done circuit and PUBLIC

by Plecto | updated June 13, 2012

Auido Amp Driven From Phototransistor Example

Auido Amp Driven From Phototransistor Example PUBLIC

This is an example of an audio amplifier meant to let you "hear" when there is light present.

by hevans | updated June 13, 2012

amplifier   audio   high-pass   low-pass  

Op-amp input

Op-amp input PUBLIC

by clabaccchio | updated June 13, 2012

Trafo se zatížením

Trafo se zatížením PUBLIC

by sourzZ | updated June 13, 2012

Trafo nakrátko

Trafo nakrátko PUBLIC

by sourzZ | updated June 13, 2012

Trafo naprázdno

Trafo naprázdno PUBLIC

by sourzZ | updated June 13, 2012

Workforce Spotlight 800-8350-H

Workforce Spotlight 800-8350-H PUBLIC

Incomplete Workforce Spotlight circuit. Once I figure out what each of these components are, I'll probably strip it for parts.

by lucasmoten | updated June 13, 2012

light   parts  

Leonardo Intersection

Leonardo Intersection PUBLIC

by Handler | updated June 13, 2012

flip clock coils

flip clock coils PUBLIC

by haarts | updated June 13, 2012

clock   coil  

Ambient Light

Ambient Light PUBLIC

by nadr0j | updated June 13, 2012

Op amp.

Op amp. PUBLIC

by drummduck | updated June 12, 2012

cc/cv power supply

cc/cv power supply PUBLIC

use this as a constant voltage or constant current power supply. Modify V1 for voltage limit, I1 for current limit (diode acts like an ideal diode). replace R1 with your circuit.

by jondrums | updated June 12, 2012

ERA

ERA PUBLIC

by Mastermime | updated June 11, 2012

Tags

555   7805   ac-to-dc   active-filter   amplifier   analog   and   anode   attenuator   atx   audio   automotive   band-reject   bandgap   behavioral   bias-point   bjt   bode   bridge-rectifier   button   calculator   cascaded-filters   cascode   cathode   cmos   colpitts   compensation   constant-current-source   current-limiting   current-mirror   current-monitor   current-regulator   dac   dc-to-ac   device-modeling   differential   differentiator   digital   diode   divider   emitter-follower   feedback   filter   flyback   flyback-diode   frequency-domain   full-wave   guitar   ham-radio   high-pass   high-speed   high-voltage   hv   hysteresis   ic   ignition-coil   induction   inductive   inductive-load   initial-conditions   instrumentation-amplifier   integrator   inverting   jfet   laplace   led   led-array   level-shift   lighting   lipo   lm317   load-cell   logic-gate   low-pass   mechanical   microcontroller   microphone   mosfet   motor   multivibrator   non-inverting   nonlinear   nor   notch   ohms-law   op-amp   optical   or   oscillator   parallel   passive   passive-filter   pcb-design   phase-shift   photodiode   photoresistor   phototransistor   piezo   plants   potentiometer   power   power-supply   power-supply-unit   preamp   pull-down   pull-up   pwm   rc   relaxation-oscillator   relay   resistor-ladder   resonance   rf   rlc   rom   saturation   schmitt-trigger   sensor   series   servo-motor   signal   spark-plug   stability   stepper   summing   superposition   switching   time-constant   transformer   transistor   translinear   twin-t   voltage-divider   voltage-regulator   waveform-arithmetic   wiring   xnor   xor   zener-diode   zero-voltage-switching  

About CircuitLab

CircuitLab is an in-browser schematic capture and circuit simulation software tool to help you rapidly design and analyze analog and digital electronics systems.