Now showing circuits 31321-31340 of 53647. Sort by
|
|
MOSFET and resistor NOR gate PUBLICTwo n-channel MOSFETs plus one pull-up resistor form a two-input NOR logic gate. by CircuitLab | updated June 08, 2017 |
|
|
MOSFET and resistor NAND gate PUBLICTwo n-channel MOSFETs plus one pull-up resistor form a two-input NAND logic gate. by CircuitLab | updated June 08, 2017 |
|
|
JFET-based electret microphone amplifier PUBLICMost electret microphone modules today come with a built-in JFET to help provide a low-impedance output and noise resistance, but these must be biased properly. by CircuitLab | updated June 08, 2017 |
|
|
LEDs with resistor biasing PUBLICLEDs are usually found with a resistor in series to select the desired current (and therefore brightness and power consumption). by CircuitLab | updated June 07, 2017 |
|
|
Laplace transform step response and Bode plot PUBLICCircuitLab can also handle arbitrary Laplace transform functions, and can produce step response plots in the time domain and Bode plots in the frequency domain. by CircuitLab | updated June 07, 2017 |
|
|
Diode turn-off time PUBLICDiodes can take a surprisingly long time to turn off, as we show in this demo. by CircuitLab | updated June 07, 2017 |
|
|
Diode full-wave rectifier PUBLICFour diodes (a "bridge rectifier") plus a capacitor can be used to rectify AC into DC, with conduction over most of the the input power cycle. by CircuitLab | updated June 07, 2017 |
|
|
Diode half-wave rectifier PUBLICA single diode plus a capacitor can be used to rectify AC into DC, but often with a lot of ripple at the output. by CircuitLab | updated June 07, 2017 |
|
|
BJT current mirror PUBLICTwo NPN bipolar transistors form a current mirror. by CircuitLab | updated June 07, 2017 |
|
|
BJT Cascoded Active-load Differential Amplifier with CMFB PUBLIC10 BJTs and an op-amp provide a gain of almost +70dB and about 16kHz bandwidth. A cascoded active load provides high-impedance load for the emitter-coupled pair. by CircuitLab | updated June 07, 2017 |
|
|
BJT audio amplifier PUBLICA one-transistor amplifier, intended to amplify audio picked up by a piezoelectric transducer. by CircuitLab | updated June 07, 2017 amplifier audio bjt filter frequency-domain high-pass low-pass |
|
|
7805 & Wall-wart Experiencing Voltage Drop-out PUBLICA 7805 linear voltage regulator can't quite maintain its output voltage. Can you fix it? by CircuitLab | updated June 07, 2017 |
|
|
555 Timer as Pulse Width Modulation (PWM) Generator PUBLICA 555 Timer can be used with variable "control" input to create a pulse width modulation (PWM) generator with its digital duty cycle varying based on an analog input voltage. by CircuitLab | updated June 07, 2017 |
|
|
555 Timer as Astable Multivibrator (Oscillator) PUBLICA 555 timer can be used with a few resistors and a capacitor to make an oscillator, switching states as the capacitor charges and discharges. by CircuitLab | updated June 07, 2017 |
|
|
half bridge rectifier PUBLICby mattissa | updated June 07, 2017 |
|
|
JOE PUBLICby Autarchex | updated June 06, 2017 |
|
|
sklfp PUBLICby Autarchex | updated June 05, 2017 |
|
|
non-inv B PUBLICby adebayae | updated June 05, 2017 |
|
|
Audio Filter v1 PUBLICby garrettosborne | updated June 01, 2017 |
|
|
Krell KSA-50MKII PUBLICby jmyres | updated May 31, 2017 |
CircuitLab is an in-browser schematic capture and circuit simulation software tool to help you rapidly design and analyze analog and digital electronics systems.
| New @ CircuitLab |
|---|
|
vanderghast commented on question: |
|
Dan.Ka replied to discussion: |