|
|
|
| Username | signality |
| Member Since | March 7, 2012 |
Now showing circuits 221-240 of 310. Sort by
|
|
Ramped sources 01 PUBLICUsing time 'T' in expressions to generate ramped behavioural sources. Simulate > Time Domain > Run Time-Domain Simulation by signality | updated July 12, 2012 |
|
|
Simple laplace 01 PUBLICNote: this is now fixed in CL. Something not quite right in the AC simulator. by signality | updated July 12, 2012 |
|
|
sensor amp 01 PUBLICSensor amplifier with swept 50k,10k,0 output resistance. Click on blue "Open in editor" button then Simulate > Time Domain > Run Time-Domain Simulation by signality | updated July 12, 2012 |
|
|
behavioural linear regulator 01 PUBLICBehavioural linear regulator. Can also be realised using a behavioral voltage source. by signality | updated July 12, 2012 |
|
|
behavioural opamp 02 PUBLICUsing the TANH() function, a near ideal behavioural opamp or comparator with a rail to rail limited output voltage swing can be made. This model is almost the same as behavioural opamp 01 except that... by signality | updated July 12, 2012 |
|
|
multiple decoupling capacitors 01 PUBLICAn example of what happens when decoupling capacitors are put in parallel. SImulate > Frequency Domain > Run Frequency-Domain Simulation Note that an LTspice simulation can be downloaded in:... by signality | updated July 12, 2012 |
|
|
opamp supply pins 01 PUBLICThe supply pins on CL opamps are not polarity sensitive. You can set either supply pin to any voltage and the other to any other voltage and the model will correctly pick up which is the highest... by signality | updated July 03, 2012 |
|
|
behavioural opamp 01 PUBLICUsing the TANH() function, a near ideal behavioural opamp or comparator can be made. by signality | updated July 03, 2012 |
|
|
vreg and schmitt 01 PUBLICAttempting to make Tiefentladeschutz simulate properly in a DC sweep. Replaced opamp with behavioural model. by signality | updated July 03, 2012 |
|
|
Multi-winding transformer 01 PUBLICAn ideal transformer with a primary inductance and 3 windings in 1:3:5 turns ratio. This transformer does not work down to DC because the primary inductance shorts out the signal source at DC. by signality | updated June 29, 2012 behavioural-transformer ideal-transformer multiwinding-transformer transformer |
|
|
3 inverter oscillator 01 PUBLICA 3 inverter oscillator. From Figure 2 of: Application Note 118 CMOS Oscillators www.fairchildsemi.com/an/AN/AN-118.pdf Simulate > Time Domain > Run Time Domain Simulation by signality | updated June 22, 2012 3-inverter-oscillator logic-gate-oscillator oscillator three-inverter-oscillator |
|
|
Simple sawtooth oscillator 01 PUBLICSimple sawtooth oscillator. by signality | updated June 22, 2012 |
|
|
3X Op-amp 02 PUBLICby signality | updated June 20, 2012 |
|
|
Buffer latch 02 PUBLICby signality | updated June 19, 2012 |
|
|
spark gap 02 PUBLICA simple spark gap / arc function. Same basic functionality as spark gap 01 but does simulate in CL. :) by signality | updated June 19, 2012 |
|
|
Guitar Tone Stack 01 PUBLICExample guitar tone stack. From: http://www.duncanamps.com/tsc/ by signality | updated June 18, 2012 |
|
|
diode pump 02 positive output PUBLICUsing a simple diode pump driven from a pulsed voltage source to generate a supply rail above an existing positive rail. by signality | updated June 15, 2012 |
|
|
diode pump 01 negative output PUBLICUsing a simple diode pump to generate a negative supply rail from a pulsed voltage source. by signality | updated June 15, 2012 |
|
|
relaxation osc fixed 01 PUBLICAn opamp based squarewave relaxation oscillator. by signality | updated June 11, 2012 choosing-time-step convergence convergence-problem opamp relaxation-oscillator startup |
|
|
How to use the CCCS and CCVS elements. PUBLICAn example of how to use the CCCS and CCVS elements. Simulate > Time Domain > Run Time-Domain Simulation by signality | updated June 09, 2012 |